X Y Z axis claw machine mechanism diagram — Hiclawcrane

How X/Y/Z Movement Works in a Claw Machine

What Do X, Y, and Z Mean?

The X axis moves the claw left and right, the Y axis moves it forward and backward, and the Z mechanism lowers and raises it. Together they position the claw over a prize, lower it, and return it toward the release area. These directions describe movement, not a universal motor, rail, switch, or board design.

X and Y: Positioning Over the Prize

In a typical gantry, the horizontal axes guide the carriage across the prize field. Depending on the assembly, movement can use belts, pulleys, gears, or other drive parts; rails and position sensors also vary. Do not assume each axis has the same motor or that every machine uses a limit switch at both ends. The return position and startup behavior depend on the board and model.

Motor ratings must come from the actual components. In Hiclawcrane systems, some gantries use 24V motors and others use 48V motors. The 25.7cm mini system is a separate compatibility class with different power requirements. Do not apply a blanket 12V/24V X/Y motor specification or select a motor by gantry span alone. Check the rated voltage, board output, power supply, connector and pinout, mounting dimensions, and drive interface.

Z: Lowering and Raising the Claw

The Z mechanism lowers and lifts the claw. The cable or other lift arrangement, drive motor, travel sensing, and allowable depth are specific to the machine. It is not safe to assume that every Z motor has higher torque than the X/Y motors, uses a lead screw, or has a universal depth parameter. The claw may stop according to a model-specific control sequence; check the relevant manual before adjusting its travel.

How the Movements Work Together

During a play, the player positions the claw using X and Y inputs. The drop command begins a board-controlled sequence in which the claw lowers, attempts to grip a prize, lifts, moves toward a release position, and opens. The precise timing, whether the axes can move simultaneously, and the method for detecting position vary by board and cabinet. An indicated strength or payout event does not guarantee that a prize is delivered.

Belts, Gears, and Rails

Some assemblies use belts and others use gears or different guides. A belt can show damage, looseness, or contamination; a geared drive can also wear, bind, or lose proper engagement. Neither design is automatically more precise, maintenance-free, or longer-lived for every cabinet. Follow the assembly's instructions for tensioning, cleaning, and lubrication rather than applying one general rule to all rails and drives.

First Checks by Symptom

  • One axis will not move: identify the axis and check its travel path, drive parts, relevant input, connectors, and the board's model-specific diagnostics before ordering a motor.
  • Moves by itself in one direction after a credit: Hiclawcrane's field check starts with the corresponding joystick microswitch or direction signal. With power off, isolate that input according to the board wiring guide; if movement stops during a controlled retest, inspect the switch and wiring. If it continues, follow the board's input and drive diagnostics.
  • Responds to one joystick direction but not the opposite: this is a different symptom. Check that direction's joystick signal and wiring first, then the applicable position sensing and board diagnostics.
  • Jerky or inaccurate movement: inspect for binding, debris, drive wear, loose connectors, and alignment. Do not conclude that voltage is insufficient without model-specific testing.
  • Z does not reach the expected depth: check for an obstruction, damaged lift part, and model-specific sensor or travel behavior. Do not increase a depth parameter blindly; the claw may strike the prize floor.

Keep hands clear during movement. Disconnect power before handling connectors or mechanical parts to prevent unintended movement, shorts, or board damage. Work on the mains inlet and AC input of the power supply requires appropriate qualifications. For detailed diagnostics, use the gantry troubleshooting guide and the manual for the actual model.

Frequently Asked Questions

Can the X and Y axes move at the same time?

Some machines allow diagonal movement and others have different control behavior. Check the installed board and observe a safe test cycle; do not assume every model responds the same way.

How do I adjust Z-axis drop depth?

First confirm the actual board and the cause of the depth problem. Inspect the lift path and relevant sensor, then follow that model's service instructions for any supported depth adjustment. Do not increase travel blindly.

What can damage an X- or Y-axis belt?

Wear, improper tension, obstruction, or a misaligned drive can contribute. Inspect when movement changes and follow the manufacturer's maintenance guidance; there is no universal six-to-twelve-month interval.

Are X- and Y-axis motors interchangeable?

Do not assume they are. Confirm rated voltage, connector and pinout, mounting geometry, shaft or drive interface, board output, and the parts specified for that machine before substituting a motor.

Related Resources

Back to blog

About the Author

Hiclawcrane Engineering Team

Claw machine manufacturer with over 20 years of experience in arcade machine design, manufacturing, and technical support. Based in Guangzhou, China.

Learn more →