Claw Machine Mainboard: Quick Answer
A claw machine mainboard coordinates the machine's game logic. Depending on the model, it reads joystick, button, limit-switch and payment inputs, and, where fitted, a prize sensor or bill acceptor. It commands compatible X/Y/Z motor-drive circuitry, the claw mechanism and other functions. The motor driver may be integrated into the board or separate, using relays or electronic switching such as MOSFETs. To select a replacement, match the motor voltage and current, drive design, limit switches, optional sensors and payment interfaces, connector pinouts, and the machine's mechanical configuration. Relay versus MOSFET alone does not establish compatibility.
What Does a Claw Machine Mainboard Do?
A mainboard coordinates a claw machine's game sequence. Depending on the model, it reads payment and player inputs, commands compatible movement and claw-drive circuitry, and may provide a service menu or diagnostic counters. It does not physically power or control every cabinet component by itself. The board, power supply, motors, claw assembly, sensors, and wiring have to work as a compatible system.
How the Control Signal Travels
In a typical compatible three-axis machine, the path is joystick → mainboard → motor driver → X/Y/Z motor → limit switch → mainboard. A direction input reaches the board, which interprets the current game state and commands the corresponding driver. The driver switches the motor power and the gantry moves. A limit switch can signal when a defined travel position is reached so the board can stop or change motion. This is position feedback, not a claim that every machine continuously measures motor position. The board and driver may be integrated or separate, and the exact wiring and return sequence depend on the model. Learn more about X/Y/Z movement.
Inputs and Outputs Depend on the Model
Inputs can include a coin acceptor, buttons, joystick direction signals, position sensors, and, on some models, a prize sensor or other payment accessory. The board or associated drive circuits can command X/Y/Z movement, claw operation, lights, and sound. A feature listed for one board must not be assumed to exist on another. Check the board model, connector labels, wiring diagram, and manual before replacing or configuring a component.
Some boards record play counts or offer strength and timing parameters. Counter definitions and settings vary; a board's programmed strength event is not proof a prize reached the chute. Do not describe a fixed play-count cycle as a guaranteed win or assume every machine has a payout counter, bill acceptor, or prize sensor.
Power Supply, Board Power, and Motor Power Are Different
In Hiclawcrane machines, the power supply receives mains AC and provides low-voltage DC outputs to compatible components. The mainboard is generally supplied with 5V DC; 12V commonly serves illuminated joysticks, buttons, and prize or win lights. Some gantries use 24V motors and others use 48V motors, depending on the board and power supply. The 25.7cm mini system is a separate compatibility class and generally uses 5V, 12V, and 24V power-supply outputs.
Do not connect 110V or 220V AC to a board based on a generic FAQ, and do not infer the motor's voltage from the board's supply voltage. Check the actual labels, wiring diagram, and rated parts for the specific model before diagnosis or replacement. The power inlet, switch, fuse, and AC input side of the power supply are mains-voltage areas; electrical work there requires appropriate qualifications.
How to Choose a Replacement Mainboard
Before ordering an OEM or replacement board, identify the existing board and the machine it controls. A similar-looking board is not necessarily a drop-in replacement. Ask the supplier to confirm compatibility against the board label, wiring diagram, connector photos, motor ratings, and any installed sensors or payment devices.
- Motor voltage: Match the board and its drive circuitry to the actual motor supply and motor ratings. Do not treat a 24V gantry, a 48V gantry, and the 25.7cm mini system as interchangeable.
- Motor current: Check that the relevant driver or external drive hardware is rated for the motors' operating and start-up demands. The board's logic supply voltage is not its motor-current rating.
- X/Y/Z configuration: Confirm the supported axes, drive arrangement, travel and return behavior, and claw operation against the machine's wiring diagram.
- Limit switches: Compare the number, type, wiring, and connector pinout of the position or end-stop inputs.
- Prize sensor: If one is installed, confirm the input and detection behavior for that exact board. Do not assume every mainboard supports prize detection.
- Payment interfaces: Confirm the coin acceptor's signal, voltage, and connector. If the cabinet uses a bill acceptor, verify that the board supports its interface too; not every machine has one.
- Connectors and harness: Compare every connector and pin assignment rather than relying on plug shape or the board's appearance. Never move a harness onto an unverified pinout.
- Game settings: Check that the specific firmware supports the required credit, game-time, movement, claw, and diagnostic settings. Record the old board's settings before removal.
- Replacement support: For a commercial machine, ask whether a matching harness, board manual, replacement units, and model-specific technical support will remain available.
Where specifications are missing, get written confirmation for the exact model before buying rather than guessing from a generic mainboard listing.
What Settings Might Be Available?
- Game setup: payment credits and play timing where supported.
- Movement: travel, return, or calibration parameters where supported.
- Claw behavior: grab and hold settings, and on some boards a play-count or payout-related control. These do not guarantee a prize delivery.
- Diagnostics: test menus or counters on boards that provide them.
Menu names, ranges, saving behavior, and even the presence of each setting differ by board and firmware. Use the manual for the exact version. Record original values before making a change, adjust one supported setting at a time, and verify operation with actual prizes.
Claw Machine Mainboard Troubleshooting
A symptom is not a diagnosis. Check the related mechanical parts, supply, wiring, and inputs before replacing the board.
| Symptom | Check before blaming the mainboard |
|---|---|
| One X, Y, or Z axis does not move | Motor and supply, harness and connectors, limit switch, mechanical obstruction, and the relevant driver or board output. |
| Claw does not operate | Claw assembly, wiring, compatible output or drive circuit, and model-specific settings. |
| Prize is not detected | Whether this model actually has a prize sensor; then sensor alignment, wiring, power, and the supported board input. |
| Coins or bills are not accepted | Installed acceptor, supply and signal wiring, credit settings, and supported interface. Check bills only if the machine has a bill acceptor. |
| Motor keeps running | Direction input, limit switch, wiring, travel obstruction, and drive or control circuit. |
| Machine powers on but does not move | Power outputs, joystick and button inputs, harness, motor drive hardware, and board diagnostics if available. |
Start with the symptom: no credit registered, no response to a joystick direction, one axis not moving, incorrect return position, or unexpected claw behavior. Check for a blocked travel path, loose or damaged connector, and the relevant input before attributing a fault to the board. For a gantry that starts moving by itself after coin insertion, Hiclawcrane's field check begins with the corresponding joystick microswitch or direction signal, not an automatic board replacement. See the gantry troubleshooting guide for that symptom.
Do not try a factory reset as a generic first step. A reset can erase settings needed for the cabinet and prizes, and the process differs by board. Save the current configuration and follow the specific board's service instructions. Stop if movement is colliding with the cabinet or wiring is damaged. Isolate power before reseating connectors to avoid shorts or unintended movement; leave work on the mains AC side to qualified personnel.
Hiclawcrane Mainboards and DIY Kits
Hiclawcrane supplies DIY claw crane machine kits and related components for overseas buyers, distributors, and OEM/ODM projects. For a DIY build, select the control system alongside the cabinet size, gantry and claw mechanism, motor specifications, limit switches, payment system, optional prize detection, and power requirements. For a replacement, provide the original board model, motor ratings, connector photos, and machine configuration so compatibility can be checked. For a custom project, discuss the mechanical and electrical system together instead of choosing a board based on its relay or driver type alone.
Frequently Asked Questions
Are claw machine mainboards universal?
No. Match the board to the machine's wiring, power supply, motors, claw assembly, sensors, and supported features. Use the same model or a replacement confirmed compatible with the complete system.
Can I upgrade a board to gain more settings?
Possibly, but extra menu options alone do not establish compatibility. Confirm connector pinout, supply and motor ratings, drive circuitry, sensors, and firmware support before changing boards.
Should I reset a board when a setting or motor seems wrong?
Not as a first step. Record existing settings and diagnose the specific input, mechanical movement, wiring, or board function. Only use the model-specific reset procedure when warranted, knowing that saved parameters may be lost.
What voltage does a claw machine mainboard use?
Check the specific board label and wiring diagram. In Hiclawcrane machines, the mainboard is generally supplied with 5V DC from the power supply; it should not be described as generally accepting 110V or 220V AC. Motors and accessories may use different DC outputs: some gantries use 24V, others 48V, while the 25.7cm mini is a separate 24V-system compatibility class.
Conclusion
Choose the mainboard as part of the complete machine, not by relay type or appearance alone. Verify motor voltage and current, driver design, connectors, switches, optional sensors and payment interfaces before buying or replacing it.
Related Resources
- How X/Y/Z Movement Works in a Claw Machine
- How Claw Machine Limit Switches Work
- How Prize Sensors Work in Claw Machines
- Coin Acceptor vs Bill Acceptor
- How a Claw Machine Mainboard Affects Claw Strength
- How a Claw Machine Gantry Works
- Engineering Knowledge — More Technical Guides
- Arcade Glossary: Main Board
- Knowledge Center
- DIY Claw Machine Kits
- Arcade Spare Parts — confirm compatibility and pack quantities before ordering